padpolt.blogg.se - Sweet home 3d dimensions

SWEET HOME 3D DIMENSIONS HOW TO
SWEET HOME 3D DIMENSIONS INSTALL
SWEET HOME 3D DIMENSIONS UPDATE
SWEET HOME 3D DIMENSIONS CODE

Now dimension lines can be drawn on any kind of surface, even on furnitures and - with some trick - even in the air! This behavior could sometimes be unwanted, so I've implemented a way to disable it holding the ALT key. This way if you place the start point on a wall, even the end point must reside on the same wall, it will never snap to the inner faces of the window or other surfaces. Moreover with this version, after you place the first point, all the subsequent points are forced to lay on the same surface the first point belongs to. I've released the version 3.0 which solves the problem you faced when placing the line close to edges.įirst of all, I've fixed a bug which was randomly picking the bad face of the clicked wall. Be sure you're respecting the above points, if doing so doesn't resolve the problem maybe I misunderstood it. If you hold SHIFT and you haven't a room where the cursor is, moving the mouse doesn't trigger any change and the line length stays zero. The "?" symbol is shown when the line is zero length, which in pratice happens just after you have placed the first point, and the cursor hasn't moved away yet.

If you need to place one or both points on the edge of a room, in order to avoid clicking outside of the room, it is easier to place the point a bit far from the edge, and move the point later close to the edge while holding the SHIFT key.

SWEET HOME 3D DIMENSIONS CODE

I could consider enforcing this by code in the future, but for now it's up to the user. you have to hold SHIFT during the whole drawing) although the plugin allows you to have the 2 points on different surfaces, doing so will break the math calculations bringing to unexpected results.

both points and offset must reside on the ceiling (i.e.

a floor) on both the start and end points (I could remove this requirement in the next release). I've added fixing them to the roadmap.Ībout your second post, here some considerations when drawing on the ceilings: About your first post, the problems are clear and I can reproduce them. Re: 3D dimension lines you for your feedback. I'm being helpful, not a dick, by reporting these.) (For anyone else: I've been assisting Daniel find issues in the Pan3DView plugin. Again, videos can be recorded on request if I'm not clear, or you can't reproduce. If I start the line on a wall without shift, then press shift, the in-motion line freezes till I release shift.

That happens if I can press shift and the mouse button at the same time, but often no line is even started. I might get a "?" in a diamond at the start point, but no elastic in-motion line until after I release shift. a wall) the elastic mouse following of the initial line simply doesn't start. I can't use shift to draw a measurement on the ceiling as described.

I can do another mini-video if you want to see the issue better than I'm describing it.Īnother "Huh?!?!" moment. Something somewhat similar happens in aerial view, but the snap to the previous view happens when releasing the mouse button after moving a point. It also yanks the point you are moving to your new viewpoint, making a mess of the dimension. It is like it is resetting to a previously stored position. In virtual viewpoint, trying to move a point causes the view to jump around on me. It's very cool to be able to do this dimensioning, but I'm struggling a bit. (1)Here some screenshots:ġ) credits to PUYBARET for part of the code.

from above or below in case of ceilings, and from back in case of transparent walls. measurement labels can be correctly seen from both sides, i.e.intelligent snap cursor: snaps to other dimensions' endpoints, and wall corners.dimensions can be edited after they have been placed.the measurement can be done in any direction, not necessarily the same of the endpoints.dimensions can be placed on floors, walls and ceilings.

SWEET HOME 3D DIMENSIONS HOW TO

The plugin comes with an integrated user guide available in english and italian under the Help > Draw3D dimension lines help menu, please take a moment to read it to learn how to use the plugin.

SWEET HOME 3D DIMENSIONS UPDATE

Please note that this plugin conflicts with the Wirings plugin versions prior to 1.2 if you are using it be sure to update to the latest version.

SWEET HOME 3D DIMENSIONS INSTALL

In order to use this plugin you have to install Pan3dView plugin version 1.7 or later. This could be useful to give precise directives to installers. This plugin brings to SH3D the capability to draw 3D dimension lines that will snap to floors, walls and ceilings, directly in the 3D view.